ASTM A291 PDF
A – 02 Standard Specification for Steel Forgings, Carbon and Alloy, for Pinions, Gears and Shafts for Reduction Gears, alloy steel forgings, carbon steel . ASTM A/AM: Standard Specification for Steel Forgings, Carbon and Alloy , for Pinions, Gears and Shafts for Reduction Gears. ASTM A Standard Specification for Steel Forgings, Carbon and Alloy, For Pinions, Gears and Shafts. Uploaded by medialeon. ASTM A Standard.
|Published (Last):||8 September 2009|
|PDF File Size:||12.69 Mb|
|ePub File Size:||13.98 Mb|
|Price:||Free* [*Free Regsitration Required]|
Optional with manufacturer and purchaser.
Join your peers on the Internet’s largest technical engineering professional community. By joining you are opting in to receive e-mail.
Committee A01 has identi? Resources Digital Transformation may be defined in a number of different ways by analysts or enterprise software vendors.
ASTM A X ASTM A – Metal and Metallurgy engineering – Eng-Tips
Prior to heat treatment for mechanical properties testingsteel materials may undergo machining and boring, after which specimens shall be stress relieved. Rough Turning and Boring S1. When agreed upon between the manufacturer and the purchaser, forgings weighing less than lb kg each rough-machined weight may be tested in lots; the number of forgings to make up a lot shall be by mutual agreement.
It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. On each forging under 8 in. Does it mean that regardless the thickness of my forgingI can only estimate mechanical properties through the HB figures? Register now while it’s still free! Brinell Hardness Number Range to to Grade Class Tensile Strength, min psi 85 80 95 95 95 MPa Charpy V-notch 3, 3A C, D When vacuum carbon deoxidation is used, silicon maximum shall be 0.
ASTM A291 Grade 5
So, first design the small diameter Pinions, Gears and Shafts per A, then choose a matching alloy in Table 1 of A for the large diameter ring gear.
Red Flag This Post Please let us know here why this post is inappropriate. Students Click Here Join Us! This abstract is a brief summary of the referenced standard. Current edition approved Apr. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.
Posting Guidelines Promoting, selling, recruiting, coursework and thesis posting is forbidden. Grade 1 shall be air cooled while Grades 2 through 9 shall be liquid quenched. The last thing you want is to have a ring gear fail in service because you decided to cut cost. Combining values from the two systems may result in non-conformance with the standard. ASTM A applies to rings a product form that are either forged or rolled. Is there any violation in designing a ring forge as per ?
In this case, thickness or diameter limitations are not applicable for tensile and impact property test requirements in Table 3. Thank you for helping keep Eng-Tips Forums free from inappropriate posts. Digital Transformation may be defined in a number of different ways by analysts or enterprise software vendors. Download Now Defense manufacturing is all about project manufacturing and project accounting. The specimens shall be machined and tested with minimum properties and test temperatures speci?
If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. A superscript epsilon e indicates an editorial change since the last revision or reapproval.
Minimum tempering temperatures shall be as follows: Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Hardness tests shall be performed at the quarter-face width of the tooth portion diameter.
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Now note the correlation between chemistries in Table 1 of each spec. The axis of the tangential test specimen shall be located as near to the surface of the forging as practicable.
When impact tests are speci? Brinell hardness tests shall be made on prepared areas on the forgings after machining to the sizes ordered by the purchaser and after stress relieving if stress relieving is required. A — 03 Standard Speci? Last previous edition approved in as A — ASTM A establishes either a diameter or thickness range for the mechanical properties on table 3 for the different classes of steel.
This specification covers normalized and tempered carbon a219, and liquid quenched and tempered alloy steel forgings for pinions, gears, and shafts for reduction gears.
The values given in parentheses are for information only. Also, one has the option to make the more easily replaced part of an assembly somewhat softer to save on eventual maintainance.
These specifications were developed for optimum gear performance.