Does anyone have a copy ofthe CBRR service manual yet? there are a few bits of service information I would like to find out about my new. Service your Honda CBRR motorcycle with a Cyclepedia service manual. Get color photographs, wiring diagrams, specifications and step-by-step. File Name: Honda CBRR Service File Submitted: Today at PM Honda CBRR Service

Author: Kazicage Mazular
Country: Burkina Faso
Language: English (Spanish)
Genre: Software
Published (Last): 25 March 2004
Pages: 53
PDF File Size: 2.86 Mb
ePub File Size: 16.37 Mb
ISBN: 210-2-89302-318-9
Downloads: 54710
Price: Free* [*Free Regsitration Required]
Uploader: Gara

I used the same magnet rod to magnetize a screwdriver for putting the shim back into place; the magnet rod itself was just too strong.

So, I guess it was a combination of a number of sites. Honda CBR Forums forums, you must first register.

If you cbr250d the cover, you can then thread a 10mm bolt into the end of the pivot rod and pull the rod out just enough to let the rocker slip back exposing the shims. I found this service manual a while back. I only removed the exhaust one and am assuming the intake one is the same.

CBRR Honda Online Motorcycle Service Manual – Cyclepedia

Originally Posted by Rudipides View Post. BB code is On. I didn’t redo the sealant as I need to take it all apart again once I get the correct shims.

I’ve seen that manual. To reinstall, hold the rocker arm in place and push the rod back into position and put the cover back on. For one thing, the U. Please enter your desired user name, your email address and other required details in the form below.


I also found some blogs about the engine and learned that on the ‘clutch’ side of the engine there are two cover screws Allen socket head near the valve cover seam that give access to the pivot rods of the rocker arms.

CBRR Service manual? – Honda CBRR Forum : Honda CBR Forums

The manual did provide the details required to depressurize and disconnect the gas line. Owners Manual in English.

The fairings are each held on by three screws; one down at the bottom on the inside, one on the side and one at the front accessed from the front. Remove Advertisements Sponsored Links. For the best viewing experience please update your browser to Google Chrome. Share Share this post on Digg Del. Quote message in reply? Password Please enter a password for your user account. Note that passwords are case-sensitive. Then flex things a bit and pop the cover off; it has two rubber grommets holding it.

There are two different types of screws; the long shouldered one goes at the front. Add Thread to del. Also, that manual doesn’t make it clear that manuall adjust the valves without removing the cams, rocker arm shaft removal is required It is not leaking though.

Found this link today: Anyone got the real one? Remove the two top screws beside the gas tank at the front you can see them when sitting on the bike. Good but this is the Owners Manual, not the service manual. It seems to be a little different from the U. Originally Posted by pgkool View Post. If you end up doing this, can you take cbr20r picture of the rubber covers and post them? The only usable access is if you remove the gas tank, the rubber shields and disconnect and tie some cables out of the way.


What information are you looking for in particular? User Tag List Dbr250r 1 of 2 1 2. It then pops out of the clips.

2011 2012 2013 CBR250R Honda Online Motorcycle Service Manual

You must take off the cover at the front of the gas tank to gain access to the tank bolt up there. Careful with the signal wires; they are color coded. This is all there is so far: Worked like a charm. Working with the shims is tricky; a magnet rod is an absolute necessity.

It is in English too! The valve cover gasket is sealed to the head surface at two places and I had to break the sealant as there was just no way to get the gasket back into the groove in the cover while putting it all together.

Related Posts